Performance Optimized Down Fire Ported 10" Enclosure | Kicker Comp GOLD10 Single 10" Ported enclosure

A stiff suspension and a strong motor is the combination that makes a vented alignment behave, because both of the things that put a peak at tuning are absent. Bl 18.4 on a ten is a serious motor, and it is doing the work that a larger, softer driver would ask the cabinet to do. The result is a passband you can EQ against rather than around. Tuning is chosen for in-car response rather than for an anechoic curve: a vehicle adds roughly 12 dB per octave below about 45 Hz, so a box tuned very low reinforces a region the cabin is already reinforcing and leaves 40 to 60 Hz thin. In this cabinet that lands at 2.9 dB of in-car spread across 25 to 60 Hz, which is where kick and bass fundamentals live.

No, and on this build in particular do not add any. Every sealed Proline X enclosure ships with polyfill pre-installed; a ported one must not, because damping material changes the effective volume the port is tuned against. The port on this cabinet is cut to 28.10 inches of centreline path for 35.0 Hz. Stuff it and you move the tuning without shortening the port, which gives you a mistuned box rather than a bigger-sounding one. The 1.34 dB passband you are paying for depends on it staying dry.

Yes, at 28 Hz, 24 dB per octave. Below tuning a vented box stops loading the cone and excursion runs away toward DC. With the filter in place this cabinet puts the Kicker Comp GOLD10 at 58 percent of its usable travel at full rated power; without it there is no meaningful number to quote, because the excursion curve does not converge. On a sealed build a subsonic filter is an improvement. Here it is required equipment.

Kicker rate the Comp GOLD10 at 400 W RMS and that is the thermal ceiling. The figures on the Performance Graphs tab are a different quantity: they are mechanical limits, the power at which the cone reaches the end of its linear travel in this specific cabinet. Here the cone sits at 58 percent of usable travel at the driver's own rating, so heat is what stops you, not travel. Final wired impedance and amplifier output are separate questions again.

Below about 21 Hz, yes. The smallest sealed box Kicker allow for it is louder down there by up to 0.9 dB, because a sealed box rolls off gently into the subsonic region where a vented one falls away steeply once it is under tuning. Above that this alignment is the louder of the two for the same power. The Performance Graphs tab plots this cabinet, 1.26 cubic feet vented at 35.0 Hz, against Kicker's minimum sealed box, 0.80 cu ft (0.80 printed, 0.77 net after the woofer), so you can see exactly where they cross.

It is a slot port formed by one folded wall: a leg down the long side of the cabinet past the woofer ring, one faceted 90 degree bend, and a leg across the end opening through a chamfered corner. On this cabinet that is 28.10 inches of centreline path and 20.3 square inches of channel, exiting a 26.5 square inch mouth. Air leaves at 13.3 metres per second at tuning against a 17.0 threshold, and the channel runs at 46 percent of its turbulence limit. One wall and one bend rather than a serpentine's three means less wall area inside the box, fewer joints to leak, and one place for flow to separate instead of three.

V-groove and dado joinery in 0.75 inch Langboard Elite MDF with a double-layer 1.5 inch baffle. The driver mounts to a 11.625 inch ring bonded under the baffle in a machined recess, carrying eight #8-32 hurricane nuts so it threads into steel rather than MDF. A windowed brace sits 2.90 inches clear of the cutout edge and 1.65 inches clear of the port terminus; the window is not weight saving, a solid panel there would split the cavity and make the box a bandpass. Walls seat into dados in both the lid and the baffle. Square corners, plush black carpet, side-mounted terminal cup.

No. This is an enclosure only, cut and folded for the Kicker Comp GOLD10 specifically. The 9.125 inch cutout, the 5.250 inch mounting depth allowance and the 1.26 cubic foot alignment all come from Kicker's published parameters for this exact driver, and the port is sized against its Xmax and power rating. It is not a universal box with a 10 inch hole in it. Bring your own driver.